Pool tables are designed for patios and indoor sports arenas. Pool is a game that most play during their leisure time with family and friends. The tables are able to last as long as 20 years with minimal maintenance when they are made from durable material. The part of the structure that is most vulnerable is the felt. In considering pool table refelting Denver residents should know the steps taken in order to come up with excellent results.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The rails should be removed after that. This is done using a crescent wrench. Bolts attaching the rails are removed. Usually, the rails are also covered by the felt so they will need to be re-felted as well. The rails will then need to be carefully set on the floor close to its position in the table so that a mistake will not be made of attaching the rail to the wrong side.
The felt that needs to be replaced gets removed using a staple remover. It is used for pulling out the staples at the felt edge. Caution should be taken to ensure there is removal of all felt from the surface of the table. The old felt should be placed on a thrash bag and disposed of later.
The new one is carefully placed while being cautious not to damage or stain it. During the process, a sharp pair of scissors is used to cut it. The borders of the table are used as the guide. There needs to be some felt left over that is to be used to re-felt the rails.
After the cut has been made, the felt is attached to the top of the table using a stapler. The stapling should start at the mid portion of one end of the felt before the right and left edges are stapled. After this, you should go to the opposite end and tightly pull the felt. It is then stapled in the same way as the previous side.
Side edges are then stapled. It is essential to ascertain that the staples are placed at the same distance from each other. They also need to be lined up in the correct way. 3 slits are cut on each pocket then the felt is wrapped and stapled on the pocket edges. Before stapling, the felt is tightly pulled.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The rails should be removed after that. This is done using a crescent wrench. Bolts attaching the rails are removed. Usually, the rails are also covered by the felt so they will need to be re-felted as well. The rails will then need to be carefully set on the floor close to its position in the table so that a mistake will not be made of attaching the rail to the wrong side.
The felt that needs to be replaced gets removed using a staple remover. It is used for pulling out the staples at the felt edge. Caution should be taken to ensure there is removal of all felt from the surface of the table. The old felt should be placed on a thrash bag and disposed of later.
The new one is carefully placed while being cautious not to damage or stain it. During the process, a sharp pair of scissors is used to cut it. The borders of the table are used as the guide. There needs to be some felt left over that is to be used to re-felt the rails.
After the cut has been made, the felt is attached to the top of the table using a stapler. The stapling should start at the mid portion of one end of the felt before the right and left edges are stapled. After this, you should go to the opposite end and tightly pull the felt. It is then stapled in the same way as the previous side.
Side edges are then stapled. It is essential to ascertain that the staples are placed at the same distance from each other. They also need to be lined up in the correct way. 3 slits are cut on each pocket then the felt is wrapped and stapled on the pocket edges. Before stapling, the felt is tightly pulled.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
No comments:
Post a Comment